Corle Building Systems Insulated Panels

FL40 panels are produced with a smooth micro-embodssed, flat 22 gauge factory coated steel exterior face for a hi-tech architectural appearance. They can be installed either vertically or horizontally. The horizontal wall assembly incorporates a clean, simple end joint design that utilizes self aligning pre-painted aluminum extrusion. Standard thickness (inches): 2,2.5,3

GENERAL WALL PANEL SPECIFICATIONS

• Standard facings: 22 gauge G-90 galvanized steel.
• Standard interior facing: 26 gauge G-90 galvanized steel, Imperial White polyester.
• Other available interior steel facings: 24, 22
• Module lengths: 8 ft. to 40 ft.
• Joinery: Offset double interlocking tongue and groove with hidden fasteneing.
• R-Values: 2 in = 16, 2.5 in. = 20, 3 in = 24
• Core: Continuously foamed-in-place urethane with nominal 2.2 to 2.5 pcf density.

PROFILED WALL PANELS SM40

The SM40 standard mesa profile panel is perfect for exterior/interior wall and ceiling applications on industrial and cold storage use buildings. The lower profile linear exterior surface simplifies flashing connections designed to inhibit moisture vapor transmission compared with other deep fluted products offered on the market. This product is also available with the mesa profile on both sides and is referred to as double mesa (DM40). Standard thicknesses (inches): 2, 2.5, 3, 4, 5, 6

MV40

The MV40 micro vee panel offers an extremely economical exterior or interior wall where a clean, flat profile appearance is desired. The nominal .2 millimeter deep stiffening beads help maintain an acceptable flatness tolerance in the light 26 gauge facings. This product is suitable for exterior applications up to 3 in. and up to 6 in. for interior use. Standard thicknesses (inches): 2, 2.5, 3, 4, 5, 6

HE40 and HE40-A

The HE40 heavy embossed panel is installed on exterior walls with a factory applied paint finish or may be field sprayed with an acceptable textured elastomeric coating. The HE40-A Adobe Texture™ panel provides a low gloss multi-textured profile and finish system that simulates a troweled stucco style appearance without the problems common to field assembled stud and stucco construction or factory sprayed composite panels.
Standard thicknesses (inches): 2, 2.5, 3, 4

General Profiled Wall Panel Specifications

• Standard facings: 26 gauge G-90 galvanized steel.
• Standard interior facing: 26 gauge G-90 galvanized steel, Imperial White polyester.
• Other available steel facings: 24, 22 (HE available in 26 ga. exterior only).
• Module lengths: 8 ft. to 67 ft.
• Joinery: Offset double interlocking tongue and groove with hidden fastening.
• R-Values: 2 in. = 16. 2.5 in.= 20, 3 in. = 24, 4 in. = 32, 5 in. = 41, 6 in. = 50
• Core: Continuously foamed-in-place urethane with nominal 2.2 to 2.5 pcf density.

INSULATED ROOF PANELS

HR3 and HR5

The HR3 (three rib) high rib panel is an economical solution to field assembled metal roofing. This product installs quickly and easily by through fastening at standing ribs into supporting structural members. The HR5 (5-rib) high rib panel was developed for long span and/or severe loading conditions. Fastening is identical to the HR3 panel. Standard thicknesses (inches): 2.5, 3, 4, 5, 6

CR2 and CR3

The CR2 (two rib) cap rib panel is designed specifically for low slope (minimum 1/4:12) hidden fastened roof applications in many cases alleviating the need for parapet wall cantilevers or perimeter fascia assemblies. The CR3 (three rib) cap rib panel offers increased spans when needed and is otherwise identical to the CR2 panel. Standard thicknesses (inches): 2.5, 3, 4, 5, 6

General Roof Panel Specifications

• Standard exterior facing: 26 gauge G-90 galvanized steel.
• Standard interior facing: 26 gauge G-90 galvanized steel, Imperial White polyester.
• Other available steel facings: 24, 22
• Module lengths: 8’ to 60’
• Joinery: Overlapping (HR series), Preformed snap-on cap (CR series)
• R-Values: 2.5 in. = 21, 3 in. = 24, 4 in. = 33, 5 in. = 42, 6 in. = 50
• Core: Continuously foamed-in-place urethane with nominal 2.2 to 2.5 pcf density.

ROOF DECK

RD5

The RD5 roof deck panel provides the steel deck, insulation and substrate for white single ply membrane or non-structural standing seam roof coverings in a single composite as opposed to rigorous and expensive field assembled roof deck systems. Advantages include longer spans between supports, a working platform during installation, superior deflection resistance, a white reflective interior and fewer trades to install. The topside substrate can be either primed steel sheet or an approved flexible facer depending on the roof covering attachment requirements. Standard thicknesses (inches): 2.5, 3, 4, 5, 6

General Roof Deck Specifications

• Standard exterior facing: 28 gauge G-90 galvanized steel.
• Standard interior facing: 26 gauge G-90 galvanized steel, Imperial White polyester.
• Other available steel facings: 24, 22
• Module lengths: 8’ to 60’
• Joinery: Overlapping
• R-Values: 2.5”=20, 3”=24, 4”=32, 5”=41, 6”=50
• Core: Continuously foamed-in-place urethane with nominal 2.2 to 2.5 pcf density.

Notes

• Corle offers embossed metal surfaces as a standard on wall panels and non-embossed (smooth) for roof exterior surfaces. Non-embossed finishes may be available on wall panels upon request depending on color, gauge and end use.
• Complete paint system specifications are available upon request.
• The standard interior paint finish for all panels is Imperial White.
• All colors, except Imperial White, are available in a fluorocarbon (PVDF) finish, upon request.
• All colors shown below are Cool Roof formulations meeting High and Low Slope ENERGY STAR specifications.

Disclaimer:
All information published and distributed is thought to be reliable and correct. Installation details are meant to represent typical product applications based on standard construction practices. It is the ultimate responsibility of the buyer or his owner or architect to verify that the product(s) selected are suitable for the specific application. In accordance with our ongoing efforts to improve our products, we reserve the right to change any information contained in our publications without notice.

Corle Building Systems
114 Rosemont Lane - Imler, PA 16655
Phone: 814.276.9611 Fax: 814-276-3307
Office Hours: 7AM-5PM Mon-Fri (Eastern Time)

Steel Buildings by Corle

INSULATED WALL PANELS

Architectural Wall Panels FL40

GENERAL WALL PANEL SPECIFICATIONS

PROFILED WALL PANELS SM40

MV40

HE40 and HE40-A

General Profiled Wall Panel Specifications

INSULATED ROOF PANELS

HR3 and HR5

CR2 and CR3

General Roof Panel Specifications

ROOF DECK

RD5

General Roof Deck Specifications

In-Stock Color and Finishes

COLOR

TYPE

Application

Std. Warranty

Notes

Insulated Panel Testing and Approvals

Tests/Approvals

Type

Click Here for Load Span Tables (PDF)

Click Here for the Corle Insulated Panels Brochure (PDF)